检索范围:
排序: 展示方式:
李明超,缪正建,刘菲,王刚
《中国工程科学》 2011年 第13卷 第12期 页码 103-107
针对水利水电工程多源地质数据的特点,充分考虑了地质精度要求、曲面连续性和数据存储量等多方面的均衡,提出并实现了基于NURBS(non-uniform rational B-splines,非均匀有理样条曲线)技术的复杂地质曲面插值—逼近拟合构造方法。该方法对于工程关键区域集中且均匀分布的原始数据,采用NURBS蒙皮插值方法,使曲面严格通过这些数据点;对于周边区域分布离散的数据,采用NURBS逼近拟合方法,使曲面在给定精度下充分逼近原始数据;最后对整体曲面的地质结构合理性、几何性和精度进行检查分析和调整。实例表明,该方法所构造的地质曲面能满足地质工程师的实际需要,并能为进一步的三维地质建模提供基础。
Wenbin LI, Hiromasa SAKAI, Shota HARADA, Yasushi TAKASE, Nao-Aki NODA
《机械工程前沿(英文)》 2011年 第6卷 第3期 页码 277-286 doi: 10.1007/s11465-011-0234-y
Steel conveying rollers used in hot rolling mills must be exchanged frequently at great cost because hot conveyed strips induce wear and deterioration on the surface of roller in short periods. In previous studies, new roller structure was considered which has a ceramics sleeve connected with two steel shafts at both ends by shrink fitting. Here, although the ceramics sleeve can be used for many years, the steel shafts sometimes have to be exchanged for maintenance and reconstruction under the corrosive atmosphere. Since the thermal expansion coefficient of steel is about five times larger than that of ceramics, it is necessary to investigate how to separate the shrink fitting system by heating outside of sleeve and cooling inside of the shaft. Although how to separate the real roller has been discussed in the previous study, the separation mechanism has not been clarified yet. Therefore, in this study, several types of more fundamental models are investigated to understand the separation mechanism of real roller by the application of the finite element method. The results may be useful for designs of new rollers.
关键词: contact ceramics thermal stress heating finite element method
与地球同步:碳氮循环在保护地球宜居性中面临的挑战 Views & Comments
Robert Socolow
《工程(英文)》 2016年 第2卷 第1期 页码 21-22 doi: 10.1016/J.ENG.2016.01.012
Investigating peak stresses in fitting and repair patches of buried polyethylene gas pipes
Reza KHADEMI ZAHEDI, Pouyan ALIMOURI, Hooman KHADEMI ZAHEDI, Mohammad SHISHESAZ
《结构与土木工程前沿(英文)》 2020年 第14卷 第1期 页码 147-168 doi: 10.1007/s11709-019-0587-6
关键词: Ansys software polyethylene buried pipelines polyethylene joints polyethylene patches peak von Mises stress soil-pipe interaction temperature variation
Uncovering the evolution of tin use in the United States and its implications
《环境科学与工程前沿(英文)》 2021年 第15卷 第6期 doi: 10.1007/s11783-021-1406-6
• US tin use decreases as the GDP value added by manufacturing sector increases.
关键词: Tin use GDP Curve fitting Logistic model Gompertz model
广域电磁法和拟流场法精细探测技术——以井工一矿水害探测为例 Article
何继善
《工程(英文)》 2018年 第4卷 第5期 页码 667-675 doi: 10.1016/j.eng.2018.09.006
井工一矿存在严重的老空区和水害。以往的单一勘探方法,如地震法、直流电法、音频大地电磁法、可控源音频大地电磁法、瞬变电磁法等,均未能探明老采空区范围和水害赋存情况。为了解决这个难题,联合采用广域电磁法和井- 地拟流场法的三位一体立体式探测技术,并利用三维反演电阻率资料精准获取富水区域和采空区的位置,确定了不同层位水的连通性,为井工一矿的安全生产提供了可靠的技术保障。结果合理、成效显著,释放了近4 km2 的可采面积。
ZHOU Xiaopeng, SU Xueli, SUN Yan
《化学科学与工程前沿(英文)》 2007年 第1卷 第2期 页码 103-112 doi: 10.1007/s11705-007-0020-x
关键词: fundamental importance single-component equilibria acceptable fitting hemoglobin chromatographic separation
LIU Xiaojia, NING Fangfei
《能源前沿(英文)》 2008年 第2卷 第4期 页码 541-549 doi: 10.1007/s11708-008-0077-3
关键词: definition objective distribution fitting precision combination numerical aerodynamic
采用线性和非线性拟合方法进行指数模型参数估计 Article
Ping YANG,Chao-peng WU,Yi-lu GUO,Hong-bo LIU,Hui HUANG,Hang-zhou WANG,Shu-yue ZHAN,Bang-yi TAO,Quan-quan MU,Qiang WANG,Hong SONG
《信息与电子工程前沿(英文)》 2017年 第18卷 第3期 页码 434-444 doi: 10.1631/FITEE.1601683
霍兵勇,易伟建
《中国工程科学》 2015年 第17卷 第1期 页码 151-160
随着实验模态分析方法的广泛应用和不断发展,在工程应用中,研究者希望能减少限制条件,增加分析的可靠性。本文发展一种识别系统模态参数的新方法,本方法无需知道系统的输入信息且不用建立系统模型,仅通过对测试记录的响应信号进行频谱分析即可识别系统的模态参数,依据系统中各响应点的信号,先采用离散反卷积方法从各响应点信号中分离出谐波参数作为初步的识别结果,在此基础之上,结合频域空间曲线拟合的方法修正识别结果中受频谱混叠影响而偏差较大的谐波参数,再联合这些已提取的谐波参数得到系统的模态参数。通过对实际结构测试数据的分析,证明本方法只用输出数据识别的模态参数与模态分析软件用传递函数识别的结果一致。
Aerodynamic impact of train-induced wind on a moving motor-van
Jiajun HE; Huoyue XIANG; Yongle LI; Bin HAN
《结构与土木工程前沿(英文)》 2022年 第16卷 第7期 页码 909-927 doi: 10.1007/s11709-022-0833-1
关键词: rail-cum-road bridge aerodynamic impact train-induced wind CFD aerodynamic force quantitative analysis fitting
一种将拓扑优化设计转化为增材制造结构的实现方法 Article
刘书田, 李取浩, 刘君欢, 陈文炯, 张永存
《工程(英文)》 2018年 第4卷 第2期 页码 277-285 doi: 10.1016/j.eng.2017.09.002
王勇,阮奇
《中国工程科学》 2006年 第8卷 第6期 页码 83-88
管内湍动流体摩擦因数是雷诺数和相对粗糙度的二元非线性函数,由Colebrook隐式方程计算摩擦因数要用迭代的方法求解,很不方便。为了得到形式简单、精度高的计算摩擦因数的显式方程,提出了二元非线性多项式智能拟合法。该法将二元非线性多项式转化成多元线性多项式并建立线性最小二乘法标准矩阵,用遗传算法结合矩阵法对多项式的项数、项型式项指数及项系数进行搜索得到最优的拟合函数式。用该法拟合了Colebrook方程解的数据,得到一个计算管内湍动流体摩擦因数的显式新方程。在雷诺数3.000≤Re≤108、相对粗糙度0≤e/d≤0.05的范围内,该方程计算结果与Colebrook方程的平均偏差为0.5%,最大偏差不超过1.8%,与实验数据偏差为2.3%。新方程具有形式简单、精度高、适用范围广的优点,且便于简化成光滑管或阻力平方区等情况下的计算摩擦因数的方程。
王海舟,李美玲,庄景云
《中国工程科学》 2011年 第13卷 第10期 页码 19-27
采用原位统计分布分析表征技术系统研究了GH169高温合金压气机盘纵断面不同部位铌分布的规律。以所得到的与样品原位置相对应的数以万计原始信号系统解析为基础,进而获得压气机盘锻件的纵断面不同部位铌的定量统计分布信息以及加工工艺过程中铌的迁移规律。准确计算判定了盘纵断面不同部位铌的最大偏析度,提出了95 %置信度时中位值置信扩展率,即统计偏析度(S)新参数,用以表征铌在压气机盘中分布的均匀度;提出了所有数据在特定含量区间(C0±R)的频度(权重)比率,即统计符合度(F)新参数,用以表征预设质量控制区间铌含量的一致性的概率。采用原位统计分布分析的表征方法,准确定量地评定了高温合金压气机盘件纵断面不同部位铌的分布均匀度和符合度,为加工后盘件的质量控制评估提供了参考。
标题 作者 时间 类型 操作
Separation mechanism for double cylinder with shrink fitting system used for ceramics conveying rollers
Wenbin LI, Hiromasa SAKAI, Shota HARADA, Yasushi TAKASE, Nao-Aki NODA
期刊论文
Investigating peak stresses in fitting and repair patches of buried polyethylene gas pipes
Reza KHADEMI ZAHEDI, Pouyan ALIMOURI, Hooman KHADEMI ZAHEDI, Mohammad SHISHESAZ
期刊论文
Analysis of statistical thermodynamic model for binary protein adsorption equilibria on cation exchange adsorbent
ZHOU Xiaopeng, SU Xueli, SUN Yan
期刊论文
New response surface model and its applications in aerodynamic optimization of axial compressor blade profile
LIU Xiaojia, NING Fangfei
期刊论文
采用线性和非线性拟合方法进行指数模型参数估计
Ping YANG,Chao-peng WU,Yi-lu GUO,Hong-bo LIU,Hui HUANG,Hang-zhou WANG,Shu-yue ZHAN,Bang-yi TAO,Quan-quan MU,Qiang WANG,Hong SONG
期刊论文
Aerodynamic impact of train-induced wind on a moving motor-van
Jiajun HE; Huoyue XIANG; Yongle LI; Bin HAN
期刊论文